泄漏电流测试仪

台湾华仪 7630 全功能接触电流测试仪 EEC 7630泄漏电流测试仪

  • 产品概述:
    ♦量测接触电流时,亦可显示人体仿真阻抗线路(MD)两端的电压 ,满足接触电流IEC 60990 标准要求
    ♦接触电流可量测 AC/DC/AC+DC ,满足医疗设备IEC 60601 标准要求
    ♦量测带宽 DC - 1MHz,符合 IEC60990 接触电流测试规范
    ♦可灵活选择MD漏电流量测点(如: IEC60065 U1&U2),符合安规标准要求
    ♦内建 7 组人体模拟阻抗(MD)与1组扩充空间,满足多种安规标准要求
    ♦可搭配华仪安规测试器组成安规六合一(ACW/DCW/IR/GB/RUN/LLT) 测试系统,缩短测试时间
    ♦MD 具有BNC量测端子,可外接示波器或电压表读取电压值,方便对MD进行校准
    ♦开机智能检测功能,自动确认仪器输出正常,确保测试的可靠度
    ♦校正及预警时间设定功能,提醒用户定期校正,确保测试质量
    ♦测试结果可储存过程中最大漏电流 (Imax),满足客户对质量的要求
    ♦可选配最大峰值 75mApeak / 有效值 35mArms 量测,满足安规机构测试验证需求
  • 型号规格: 7630

7630泄漏电流测试仪 产品介绍

具有多项专利及创新功能,兼具大功率负载量测能力,适合所有接触电流的测试应用;超大型 320 x 240 Graphic LCD ,可同时显示量测电压/接触电流及测试时间;完整的自动化接口,如网络卡、USB & RS-232、IEEE-488 (GPIB) 及其他接口,可执行自动化测试,亦可搭配华仪安规测试器,组成测试系统,提升测试效率。

 

7630泄漏电流测试仪产品特点

  • 量测接触电流时,亦可显示人体仿真阻抗线路(MD)两端的电压 ,满足接触电流IEC 60990 标准要求

  • 接触电流可量测 AC/DC/AC+DC ,满足医疗设备IEC 60601 标准要求

  • 量测带宽 DC - 1MHz,符合 IEC60990 接触电流测试规范

  • 可灵活选择MD漏电流量测点(如: IEC60065 U1&U2),符合安规标准要求

  • 内建 7 组人体模拟阻抗(MD)与1组扩充空间,满足多种安规标准要求

  • 可搭配华仪安规测试器组成安规六合一(ACW/DCW/IR/GB/RUN/LLT) 测试系统,缩短测试时间

  • MD 具有BNC量测端子,可外接示波器或电压表读取电压值,方便对MD进行校准

  • 开机智能检测功能,自动确认仪器输出正常,确保测试的可靠度

  • 校正及预警时间设定功能,提醒用户定期校正,确保测试质量

  • 测试结果可储存过程中最大漏电流 (Imax),满足客户对质量的要求

  • 可选配最大峰值 75mApeak / 有效值 35mArms 量测,满足安规机构测试验证需求

全方位模拟人体电路

提供7组人体模拟线路(MD)及8组失效模式分析(Fault Condition),模拟真实世界的各种可能触电危险状况。

图片关键词
40A

大电流负载能力

负载容量可高达40A有效值,使其适用于大电流工业产品。

测试结果一目了然

可同时显示电流测量值或MD两端电压值,清楚呈现测试结果。

7630 Details
Swappable MD

多功能替换装置

MD可抽换式设计,让使用者易于替换不同选择外,更满足快速的的校验、维修与替换。

支援界面.jpg

Specification :

INPUT

Voltage

115/230 VAC ± 15%

Frequency

50/60 Hz ± 5%

Fuse

2A Slow-Blo 250V AC

Line condition

Power Switch

Reverse polarity switch for normal condition (on / off / auto setting)

Neutral Switch

Neutral switch on/off selection for single fault condition

Ground Switch

Ground switch on/off selection for class I single fault condition

Probe Setting

Surface to Surface (PH- PL)

Surface to Line(PH - L)

Ground to Line (G - L)

Ground to Neutral (G - N)

Auto Function (G - N & G - L)

SETTING

Touch Current High Limit (RMS)

Range:

0.0uA~ 999.9uA/ 1000uA~5999uA/ 6.00mA~20.00mA

Resolution:

0.1uA/1uA/0.01mA

Touch Current Low Limit (RMS)

Range:

0.0-999.9 uA

Resolution:

0.1uA

Touch Current High Limit (Peak)

Range:

0.0uA - 999.9uA/ 1000uA - 9999uA/ 10.0mA - 30.0mA

Resolution:

0.1uA/1uA/0.1mA

Touch Current Low Limit (Peak)

Range:

0.0-999.9 uA

Resolution:

0.1uA

DISPLAY

Touch Current Display (RMS)

Range 1

0.0uA~ 999.9uA, frequency DC - 1MHz

Resolution

0.1uA

Accuracy

DC : ±2% of reading + 3counts
15Hz < f<100KHz : ±2% of reading + 3counts
100KHz < f < 1MHZ : ±5% of reading (10.0uA - 999.9uA)

Range 2

1000uA~8500uA, frequency DC - 1MHz

Resolution

1uA

Accuracy

DC : ±2% of reading + 3counts
15Hz < f<100KHZ : ±2% of reading + 3counts
100KHz < f<1MHZ : ±5% of reading (10uA - 8500uA)

Range 3

8.00mA~20.00mA, frequency DC - 1MHz

Resolution

0.01mA

Accuracy

DC : ±2% of reading + 3counts
15Hz < f < 1MHz : ±5% of reading (0.01mA -20.00mA )

Touch Current Display (Peak)

Range 1

0.0uA~ 999.9uA, frequency DC - 1MHz

Resolution

0.1uA

Accuracy

DC : ±2% of reading +2uA
15Hz < f<1MHZ : ±10% of reading +2uA

Range 2

1000uA ~ 8500uA, frequency DC - 1MHz

Resolution

1uA

Accuracy

DC : ±2% of reading +2counts
15Hz < f<1MHz : ±10% of reading +2counts

Range 3

8.0mA ~ 30.0mA, frequency DC - 100KHz

Resolution

0.01mA

Accuracy

DC : ±2% of reading +2counts
15Hz < f < 100KHz : ±10% of reading +2counts

Measuring Device Module

MD1

IEC60990 Fig4 U2, IEC 60950-1, IEC60335-1, IEC60598-1, IEC60065, IEC61010

IEC60990 Fig4 U1, IEC60065

MD2

IEC60990 Fig5 U3, IEC60598-1

IEC60990 Fig5 U1

MD3

IEC 60601-1

MD4

UL544NP, UL484 , UL923, UL471, UL867, UL697

MD5

UL544P

MD6

UL1563

MD7

IEC60950, IEC61010-1 FigA.2 (2K ohm) for RUN Test MD Circuit.

External MD

Basic measuring element 1k ohm

MD Voltage Limit

70Vdc

Leakage Current Offset

Range:

0 - 999.9uA

Resolution:

0.1uA

DUT POWER

AC Voltage

0.0-277.0V

AC Current

40Arms max continuous

Over Current Protection

50Arms, Response Time < 3 sec / 250Apeak Response Time<10u sec

AC Voltage High/Low Limit

Range:

0.0-277.0V

Resolution:

0.1V/step

AC Voltage Display

Range:

0.0 - 277.0 V

Resolution:

0.1 volt / step

Accuracy:

±(1.5% of reading + 2 counts) , 30.0 - 277.0VAC

Delay time setting

Range:

0.2 !V 999.9 seconds

Resolution:

0.1 second

Timer display

Range:

0.0 !V 999.9 seconds

Resolution:

0.1 second

Accuracy:

± (0.1% of reading + 0.05 seconds)

GENERAL

PLC Remote Control

Input - Test, Reset, Interlock & Recall File 1 through10

Output - Pass, Fail, Test-in-Process, Start-Out, Reset-Out

Scanner Control

It is applied to control Matrix Scanner (Model 7006)

Memory

50 memories , 30steps per each memory . Max. Result Display 900 data (30 memories x 30 steps)

Auto Reverse Function

AUTO Reverse ON / OFF parameter setting selection
Automatic Reverse polarity switch for normal condition in one step setting menu.
Only display maximum leakage current value.

Scope Output Interface

At rear panel BNC type to connet scope for some IEC standards test requirement and application.

Display

320 X 240 graphic LCD

LCD Contrast Setting

Range: 1-9; 1 is lightest character, 9 is darkest character.

Alarm Volume Setting

Range: 0-9; 0=OFF, 1 is softest volume, 9 is loudest volume.

Security

Lockout capability to avoid unauthorized access to test set-up programs.

Calibration

Software and adjustments are made through front panel,
Automatic Calibration alert function to signal operator when calibration is due.

Results Display

All test result information will be displayed on the screen.

Interface

RS232 standard

Safety

Product with TUV/GS certificate

Dimension

430 (W) x 133(H) x 300 (D) mm

Weight

12 Kg

STANDARD ACCESSORIES

Power Cord

X1

Fuses

X2 (Including a spare contained in the fuse holder)

Interlock Disable Key(1505)

X1

TC Receptacle Adaptor Box (1932)

X1

Hipot Test Lead for PH / PL (1101)

X2

RS232 Link Cable 1.5m(1130)

X1

DUT Power Cable 40A(1148)

X1

RUN Module (Opt.752)

W

Range : 0-1KW / 1-10KW Resolution : 0.5W / 5W

A

Range : 0.000 !V 3.500 A / 3.00 - 40.00A , Resolution : 0.001A / 0.01A

PF

0.000 -1.000

Leakage Current

Range : 0.00 - 10.00mA , Resolution : 0.01mA

AC Current High/Low Limit Setting

Range:

0-40A

Resolution:

0.01A/step

AC Current Display

Range:

0.000 !V 3.500 A / 3.00 - 40.00A

Resolution:

0.001A / 0.01A

Accuracy :

± (2 % of reading + 5 counts) / ± (2 % of reading + 2 counts)

AC Power High/Low Limit Setting

Range:

0 - 10KW

Resolution:

1W

AC Power Display

Range:

0.0 -1000.0W / 1000 - 10000W

Resolution:

0.5W / 5W

Accuracy :

±(2 % of reading + 2 counts )

Power Factor High/Low Limit Setting

Range:

0.000 - 1.000

Resolution:

0.001

Power Factor Display

Range:

0.000 - 1.000

Resolution:

0.001

Accuracy :

± (2 % of reading + 2 counts )

Leakage Current High/Low Limit Setting

Range:

0.00 - 10.00mA

Resolution:

0.01mA

Leakage Current Display

Range:

0.00 - 10.00mA

Resolution:

0.01mA

Accuracy :

± (2 % of reading + 2 counts )

Delay Timer Setting

Range:

0, 0.2 - 999.9

Resolution:

0.1

Dwell Timer Setting

Range:

0, 0.1-999.9 (0=continuous)

Resolution:

0.1

Timer display

Range:

0.0 - 999.9 seconds

Resolution:

0.1 second

Accuracy:

± (0.1% of reading + 0.05 seconds)

Power Control

It is applied to control Transformer Box (1931/1931S) or AC Power Source(6700/6800/6400 Series)

HV & GB Link Module (Opt. 753)

Max. ACW 4000VAC, DCW 4000VDC & Max. Ground Bond 40A

GPIB Interface Card (Opt. 731)

Printer Port Interface Card (Opt. 732)

Multi-function Interface Card (Opt. 751)

Including USB port A type, combination of RS-232, RS-485 port, and Bar Code Input with internal memory capability.

High Measurement Range 35mArms / 70mApeak & 4MDs (Opt. 754 )

35mArms / 70mApeak for IEC60990 fig4(U1 and U2), IEC60990 fig5(U1 and U3), UL484, IEC60601 Test Requiremt ,
Notice : Option this MD circuit have to replace MD module all MD circuits .

Transformer Box (Option) Add this option must optional Opt.752 RUN Module.

1931 Series Transformer Box
(500VA/ 1KVA/1.8KVA/3.6KVA)

Multi-Tape of 1.0, 1.06, 1.1 times of input voltage.

1931-S Series Transformer Box
(500VA/ 1KVA/1.8KVA/3.6KVA)

Multi-Tape of 0.8, 0.85, 0.9, 1.0, 1.06, 1.1 times of input voltage.

AC Power Source (Option) Add this option must optional Opt.752 RUN Module.

6800 Series Digital AC Power Source (6805, 6810 , 6820 , 6830 and 6840 )

6700 Series Programmable AC Power Source (6705, 6710 , 6720 , 6730 and 6740 )

6400 Series AC Power Source (6402, 6403, 6405, 6410 )


首页
产品
新闻
联系